Blue Star AC Error Codes List (2026): PCB Repair, Problems & Solutions by Model
Nov 21, 2026 · @ELCmart
Your Blue Star AC shows a code like E1, F2, H6 or P8 when its PCB detects a fault — this guide lists every common Blue Star AC error code by model series, what the problem is, and how to fix it, in plain language for both home users and repair technicians.
How to Read a Blue Star AC Error Code
The same code can mean different faults on different Blue Star series, so always match the code with your model series first. For example, E1 is a room sensor fault on a window AC but an EEPROM (memory) error on RA/RB/TA/TB split ACs.
- Read the code. Most split and inverter models show it on the indoor unit display (E1, F2, H6, P8). Some older models flash an LED a set number of times instead — count the blinks.
- Find your model number. It is printed on the sticker on the side of the indoor unit and on the bill. The series letters inside it (for example RA, TA, FA, VA, ZA, JA, NA, or C-Series/S-Series inverter) tell you which table below to use.
- Note when it appears. At power-on, after a few minutes of running, or only in hot weather — this helps find the cause fast.
- Reset once. Switch off from the main switch/MCB, wait 5 minutes, switch on. If the code comes back, the fault is real.
Safety first: an inverter AC PCB holds high DC voltage (around 300 V+) in its capacitors even after you unplug it. Non-technical users should only do the easy checks in this guide. Opening the PCB is for trained technicians. If your AC is under warranty, book an authorised Blue Star service visit before opening anything.Troubleshooting flowchart: what to do when a Blue Star AC shows an error code.
Blue Star Inverter AC Error Codes: Quick List
This list matches the codes published for current Blue Star inverter split ACs such as BO-IA518DLU, BO-IC312YATU, BO-IC318YBTU, BO-IC324YATU and BO-5CNHW12QATU / BO-5CNHW18QATU. Older and non-inverter series use different codes — if your series is listed in the next section, use that table instead.
| Code | Main problem | Solution |
|---|---|---|
| E0 | Indoor unit (IDU) EEPROM fault | Reset power; if it stays, reprogram or replace the indoor PCB |
| E1 | Outdoor coil temperature too high | Clean condenser coil, check outdoor fan runs, check for refrigerant overcharge |
| E2 | Indoor coil frozen protection | Clean filters and indoor coil, check indoor fan speed and gas level |
| E4 | Outdoor discharge temperature too high | Usually low gas / leak or restricted flow; clean filter, check gas and leak |
| E5 | Over-current protection (AC input on most models; compressor over-current on BO-IA518DLU) | Check supply voltage, wiring and compressor current |
| E6 | Indoor–outdoor communication error | Check signal wire continuity, loose terminals and cable earthing |
| E8 | Zero-crossing error | Switch off 5–10 minutes and restart; if it repeats, repair indoor PCB zero-cross circuit |
| EE | Outdoor unit (ODU) EEPROM fault | Reprogram or replace the outdoor PCB |
| EC | Refrigerant leak detected | Find and repair leak, vacuum, recharge by weight |
| EU | IPM over-temperature, frequency reduced | Check IPM heatsink contact and outdoor airflow |
| F1 | Indoor room temperature sensor fault | Check connector; replace sensor |
| F2 | Indoor coil temperature sensor fault | Check wiring and connector; replace sensor |
| F3 | Outdoor ambient temperature sensor fault | Check connector; replace sensor |
| F4 | Outdoor coil temperature sensor fault | Replace sensor |
| F5 | Outdoor discharge temperature sensor fault | Replace sensor |
| H6 | Indoor fan motor fault | Check motor wires (rodent damage), motor, then indoor PCB |
| L1 / L2 | Input voltage too high / too low | Check mains voltage; install a stabiliser |
| L3 | Outdoor BLDC fan motor fault | Check fan blade, motor plug, motor and fan drive |
| L4 | Phase current sampling abnormal | Outdoor PCB current-sense fault; repair or replace board |
| LC | Compressor start failure / out of step | Check compressor windings, IPM and voltage |
| P3 | Compressor overload / drive phase over-current | Check gas pressure, condenser airflow, compressor |
| P4 | DC bus voltage high or low | Check input voltage, rectifier, DC bus capacitors |
| P5 | Compressor phase over-current | Check compressor wiring and current before resetting |
| P7 | IPM error | Test IPM; replace module or outdoor board |
| P8 | IPM over-temperature | Check heatsink screws and paste, outdoor fan, gas |
| PH | AC over-voltage / under-voltage | Install stabiliser; check house wiring and earth |
| Code | Main problem | Solution |
|---|---|---|
| DH | DC bus over-voltage | Check mains voltage and DC bus capacitors |
| DL | DC bus under-voltage | Check mains voltage, rectifier, capacitors |
| HE | Compressor over-current (hardware detection) | Check compressor windings and IPM |
| HP | PFC over-current (hardware) | Check PFC circuit and reactor wiring |
| PC | PFC over-current (firmware) | Check PFC circuit and supply |
| IP | Phase leakage | Check compressor insulation to body and wiring |
| LO | Compressor step-out | Check U/V/W wiring, compressor, IPM |
Extra Codes on BO-IA518DLU
This model uses these additional codes (the rest match the table above).
One website lists E1 as a communication error on the BO-IC3xxY models. If E1 appears and the outdoor unit never starts, check the communication wire as well.
Blue Star AC Error Codes by Model Series
Match the series letters in your model number with the headings below. Series names are as listed by published service guides; if your model isn’t listed, use the quick list above and confirm with your user manual.
Window AC – L Series and G Series
| Code | Main problem | Solution |
|---|---|---|
| E1 | Room temperature sensor failure | Reconnect sensor wire; replace sensor; check PCB if sensor is fine |
| E2 | Evaporator coil sensor failure | Reconnect or replace the coil sensor |
Window AC – Y, R and M Series
| Code | Main problem | Solution |
|---|---|---|
| Er | Indoor ambient sensor failure | Heat can melt the sensor terminal; reconnect or replace sensor |
| En | Evaporator pipe sensor failure | Fix root cause (gas or PCB), then reconnect or replace sensor |
| Eo | Condenser pipe sensor failure | Check gas, inspect PCB, replace sensor if damaged |
| Ed | Evaporator defrosting | Dirty filter, dirty coil or low fan speed; clean filters and coil, check fan |
Split AC – 2-star RA/RB, 3-star TA/TB, 5-star DA/DB, 3-star FA/FB/FC
| Code | Main problem | Solution |
|---|---|---|
| E1 | EEPROM error | Indoor PCB memory fault; authorised technician replaces/reprograms board |
| E2 | Zero-crossing error | Repair zero-cross circuit on indoor PCB |
| E3 | Indoor fan speed out of control | Replace fan capacitor; check PG motor and its feedback |
| E4 | Compressor over-current (4 times) | Check wiring and input current; don’t keep resetting, it can damage the compressor |
| E5 | Room temperature sensor open/short | Reconnect or replace sensor |
| E6 | Evaporator sensor open/short | Reconnect or replace sensor |
| E7 | Condenser coil sensor open/short (FA/FB/FC only) | Reconnect or replace sensor |
| EC | Refrigerant leak (FA/FB/FC only) | Find leak, repair/replace pipe, recharge gas |
| E9 | Indoor–outdoor communication error | Check and replace broken connecting wire |
Split AC – 3-star VA/VB/VC/VD, 2-star OA/OB/OC, 5-star ZA/ZB/ZC/ZD, 5-star SA/SB, SAF/ZAF, 3HS18TAT
| Code | Main problem | Solution |
|---|---|---|
| F1 | Indoor ambient sensor open/short | Check connector; reconnect or replace sensor |
| F2 | Indoor evaporator sensor open/short | Check connector; reconnect or replace sensor |
| H6 | Indoor fan (PG motor) not running | Check PCB connector and solder joints; replace capacitor or motor |
| C5 | Jumper cap fault | Jumper cap missing or in wrong pins; reseat or replace |
| U8 | PG motor zero-cross circuit fault | Repair zero-cross circuit on indoor PCB |
| E5 | Over-current protection | Check fuse and MCB; check supply voltage if it repeats |
| FA | Low frequency due to high pipe temperature | Usually gas problem; check gas pressure |
| FH | Low frequency, anti-freeze | Indoor fan problem; check motor and capacitor |
Split AC – Old Star-Rated, Non-Star, DC Inverter C-Series and S-Series
| Code | Main problem | Solution |
|---|---|---|
| E0 | Low running frequency due to low voltage | Check input voltage; use a stabiliser |
| E1 | High-pressure protection | Clean condenser; check pressure switch |
| E2 | Indoor anti-freeze protection | Restart; clean filter/coil; technician if it repeats |
| E3 | Low-pressure protection | Check gas level and low-pressure switch |
| E4 | Compressor discharge problem | Air in system or blocked condenser; technician vacuums and recharges |
| E5 | Low voltage / over-current (overload on S-Series) | Reset MCB; use a stabiliser |
| E6 | Communication failure | Check connecting wires; replace damaged cable |
| E7 | Mode conflict | Check indoor/outdoor unit compatibility |
| E8 | Anti-high-temperature protection | Low refrigerant flow; check gas |
| E9 | Anti-cold-wind protection | Check pressure; check gas charge |
| F1 / F2 | Indoor ambient / evaporator sensor open or short | Reconnect or replace sensor |
| F3 / F4 | Outdoor ambient / condenser sensor open or short | Reconnect or replace sensor |
| F5 | Discharge sensor open or short | Check wiring and fuse; replace sensor |
| F6 | Low frequency, cooling overload | Blower motor issue; replace capacitor or repair motor |
| F7 | Oil return in cooling mode | Check oil return valve |
| F8 | Low frequency, over-current | Check supply and wiring |
| F9 | Low frequency, high discharge | Clean condenser; check gas and airflow |
| H1 | Defrost | Normal in heating mode; wait and restart |
| H2 | Static dust removal protection | Clean the filters |
| H3 | Compressor overload protection | Check compressor and its overload; find cause before resetting |
| H4 | System abnormal | Full check of fan speed, gas and compressor |
| H5 | IPM module protection | Check IPM, compressor current and supply |
| H6 | No feedback from indoor fan motor | Check motor plug, wiring and PCB fan circuit |
| H7 | Synchronisation failure | Check indoor/outdoor PCB compatibility and wiring |
| H8 | Water-full (portable AC) | Empty the water tank |
| H9 | Electric heater fault | Repair or replace heater |
| C5 | Jumper cap fault | Reseat or replace jumper |
| U1 | Compressor phase current detection fault | Check current-sense circuit on outdoor PCB |
| U3 | DC bus voltage drop | Check input voltage; use stabiliser |
| U5 | Unit current detection fault | Check installation and outdoor PCB |
| U7 | 4-way valve abnormal | Check valve coil; replace valve |
| U8 | PG motor zero-cross fault | Repair indoor PCB zero-cross circuit |
| U9 | Outdoor zero-cross fault | Repair outdoor PCB zero-cross circuit |
| P5 | Compressor phase over-current | Check current and wiring before resetting |
| P7 | IPM temperature sensor / IPM error | Reconnect sensor; check IPM and gas flow |
| P8 | IPM high temperature | Check heatsink, outdoor fan and gas |
| PH | DC bus voltage too high (S-Series) | Over-voltage; use stabiliser |
| PL | DC bus voltage too low | Fix voltage fluctuation |
| PU | Capacitor charging fault | Check DC bus capacitor and charging circuit |
| HC | PFC protection | Check PFC circuit, wiring and MCB |
| LC | Compressor start failure | Check all circuits, compressor and IPM |
| L3 | Outdoor fan module protection (S-Series) | Check and repair outdoor fan motor |
| EE | EEPROM error | PCB memory fault; technician needed |
| EU | Frequency limited, IPM high temperature | Check IPM heatsink contact and outdoor airflow |
| FH | Frequency limited, anti-freeze | Check indoor fan motor and capacitor |
Split AC – 3-star JA, JB, J3
| Code | Main problem | Solution |
|---|---|---|
| F1 | Room temperature sensor error | Reconnect or replace sensor |
| F2 | Pipe temperature sensor error | Reconnect or replace sensor |
| F4 | PG motor error | Check indoor fan motor and feedback |
Split AC – 2-star NA, NB, NM3 and 3-star HAF
| Code | Main problem | Solution |
|---|---|---|
| E1 | Air intake temperature sensor abnormal | Reconnect or replace sensor |
| E2 | Outdoor coil sensor abnormal | Reconnect or replace sensor |
| E3 | Indoor coil sensor abnormal | Replace sensor |
| E4 | Indoor PG motor feedback abnormal | Repair or replace fan motor |
Blue Star AC PCB Repair Guide (For Technicians)
Most Blue Star PCB faults come from voltage surges, loose connectors, moisture, or lizards and insects inside the board area. Check the cheap parts first before replacing the full PCB.
Which section of the inverter outdoor PCB to check for each error code.
Before you start: switch off the MCB, wait at least 5 minutes, and discharge the DC bus capacitors on inverter outdoor boards. Take a photo of every connector before removing it.
- Look at the board. Check for burnt marks, bulged capacitors, cracked solder joints near relays and connectors, corrosion, and insect or lizard remains. Clean with IPA and a soft brush.
- Check the input fuse and varistor (MOV). A blown fuse with a burnt MOV usually means a high-voltage surge. Replace both, then find why the surge happened (no stabiliser, loose neutral).
- Check the power supply (SMPS) outputs. Measure the low-voltage rails on the indoor PCB (usually 12 V and 5 V DC). No 5 V = display dead, no beep, no remote response.
- Test the sensors (F1–F5, E5/E6, Er/En codes). Unplug and measure resistance. On models like BO-IA518DLU, the room, indoor coil, outdoor ambient, outdoor coil and discharge sensors are all 10 kΩ types. Some outdoor boards use a higher-value sensor (about 45 kΩ), so check the value marked on the sensor or in the service manual. Open (infinite) or shorted (near 0 Ω) = replace the sensor. If the sensor is fine, check the connector and the PCB sensor circuit.
- Indoor fan / PG motor (H6, E3, F4, U8 codes). Check the fan capacitor, the motor plug, and the hall-sensor feedback wire. If the motor turns by hand and the capacitor is good, test the fan triac/driver on the PCB and the zero-cross circuit.
- Communication error (E6, E9). Check the indoor–outdoor cable for cuts and loose terminals, and that L, N and signal wires are not swapped. Measure the signal line voltage while running; no change = faulty communication circuit (optocoupler) on one of the boards.
- Outdoor inverter board (P, L, H5, LC, PH, PU codes). Test the bridge rectifier, DC bus capacitors, PFC section and the IPM module (diode test between P/N and U/V/W). Check the IPM heatsink screws and thermal paste. Test compressor windings: U-V, V-W and W-U should read equal low ohms and none should touch the body.
- EEPROM errors (E0, EE, E1 on RA/TA/FA series). Reseat the board and reset power. If it stays, the EEPROM needs reprogramming with the correct data or the board must be replaced with the same part number.
- Replace with the right part. Use the same PCB part number printed on the board. A wrong board can show communication or mode-conflict errors.
When to replace instead of repair: a burnt IPM with track damage, repeated EEPROM errors, or a board that failed after a heavy surge is usually cheaper and safer to replace. Always install a stabiliser after a surge-related repair.
Step-by-Step Blue Star AC Repair by Error Code
Use these procedures after matching your code in the tables above. The values given are typical for inverter split ACs; the service manual for your exact model is the final reference.
Tools needed: digital multimeter (with diode test and capacitance), clamp meter, insulation tester (megger) if available, manifold gauge set for R32/R410A, vacuum pump with micron gauge, insulated screwdrivers, soldering iron, IPA cleaner, and a resistor or bulb for discharging capacitors.
1. Sensor Errors (F1, F2, F3, F4, F5, b5; E5/E6 on RA/TA series; Er/En/Eo on window ACs)
- Switch off the MCB and wait 5 minutes.
- Find the sensor plug on the PCB. On BO-IA518DLU: indoor room sensor = red plug, indoor coil = white; outdoor ambient = white, outdoor coil = blue, discharge = red.
- Unplug it and check the pins for rust, burning or loose crimping.
- Measure resistance across the sensor. A 10 kΩ sensor reads about 10 kΩ at 25 °C, more when cold, less when warm. OL (open) or near 0 Ω (short) = replace.
- Hold the sensor tip in your hand. The reading should fall slowly and smoothly; jumping values mean a bad sensor.
- If the sensor is good, power the board and measure DC voltage at the empty sensor socket. About 5 V means the PCB side is fine; 0 V points to a fault in the board’s sensor circuit or a broken track.
- Fit a sensor of the same value, put it back in the same pocket or clip on the pipe, and reset the AC.
2. Communication Error (E6; E9 on RA/TA series)
- Check that the terminal numbers match at the indoor and outdoor terminal blocks (L, N, signal, earth). Swapped wires are common after shifting an AC.
- Look for joints, cuts or rodent damage on the interconnecting cable. Check each core end-to-end for continuity and make sure no core touches another.
- Check the earth wire and the shielded cable grounding.
- Power on and measure AC voltage between L and N at the outdoor terminal (about 230 V). No voltage = indoor relay or wiring fault.
- Measure the signal wire against N with the AC running. It should show a changing DC voltage. A steady reading means one board is not sending data.
- Check the outdoor board is alive: fuse, LED, rectifier and SMPS. A dead outdoor board gives E6 too.
- Change a board only after the wiring is confirmed good. After replacing a board, confirm the part number matches the model, or you may get mode-conflict or sync errors (E7, H7).
3. Indoor Fan Motor Errors (H6; E3 on RA/TA; F4 on JA/JB; E4 on NA/NB; U8)
- With power off, turn the blower by hand. If it is tight or rubbing, clean the blower wheel and check the bearing.
- Check the motor wires for rodent damage and the plug on the PCB.
- AC (PG) motor: test the fan capacitor against its rated µF and measure the motor windings. The PG feedback plug has 3 wires (5 V, ground, signal); turning the blower by hand should make the signal pulse between 0 and 5 V.
- BLDC motor (newer inverter models): the plug usually carries about 310 V DC, 15 V DC, a speed signal (Vsp) and a feedback signal (FG). If 310 V, 15 V and Vsp are all present and the motor does not run, replace the motor.
- If the supply or speed signal is missing, the indoor PCB is faulty (fan triac, driver or zero-cross circuit). Replace the motor first only if the motor tests bad, then the PCB.
4. Power Module and Voltage Errors (P7, P8, EU, PH, P4, L1, L2, DH, DL, PU, HC, HP, PC)
- Switch off and discharge the DC bus capacitors through a resistor or bulb. Confirm below 10 V with the meter before touching anything.
- Measure the mains voltage at the outdoor unit while it runs. Large swings or very high or low voltage are the most common cause — fit a proper stabiliser and fix loose neutral or earth.
- For P8 and EU (heat): check the outdoor fan runs, the condenser is clean, the IPM heatsink screws are tight, and the thermal paste is not dry. Re-apply paste if needed.
- Test the IPM on diode mode with the compressor wires removed: red probe on U, V or W and black on P should read about 0.3–0.6 V; red on N and black on U, V or W should read the same. Reversed probes should read OL. 0 V on any pair = shorted IPM.
- Check the bridge rectifier, and the DC bus capacitors for bulging or low capacitance. With power on, the DC bus is normally about 310–340 V.
- For PFC codes (HC, HP, PC), check the PFC reactor wiring and the PFC switching device and diode.
- If P7 stays even though the IPM tests fine, the fault is in the IPM driver or its temperature sensing. Replace the outdoor board with the same part number.
5. Compressor Errors (LC, LO, P5, P3, HE, H3; E4 on RA/TA series)
- Do not keep resetting these codes. Repeated restarts can burn the compressor or IPM.
- Remove the U, V, W wires. Measure U–V, V–W and W–U. All three should be equal and low (a few ohms). Unequal or open = compressor winding fault.
- Check each terminal to the compressor body. The multimeter should read OL; a megger should read above 2 MΩ. A low reading = grounded compressor (also causes the IP code).
- Check the U, V, W order and crimps against the wiring diagram. A wrong order or loose terminal causes step-out (LC, LO).
- Check gas pressures. Overcharge or a blocked condenser raises compressor current.
- If windings, insulation and IPM are all good but the compressor still won’t start and draws very high current, the compressor is mechanically stuck.
6. Gas and Temperature Errors (EC, E1, E4, E2, FA, E8 on C/S series)
- Clean the filters, indoor coil and outdoor coil, and confirm both fans run.
- Connect the gauge to the service port and compare the running pressure with the chart for your refrigerant in the service manual.
- Low pressure, poor cooling, plus EC or E4 = gas leak. Test flare joints with soap water first (the most common leak point), then the indoor coil and outdoor coil.
- High pressure with a hot outdoor coil plus E1 = dirty condenser, outdoor fan fault, or overcharge.
- Repair the leak, pressure-test with dry nitrogen, vacuum to below 500 microns, and charge by weight as per the nameplate.
- R32 gas is mildly flammable. Never braze with gas in the system, and keep the area ventilated.
7. EEPROM Errors (E0, EE; E1 on RA/TA/DA/FA series)
- Switch off the MCB for 5 minutes and restart.
- Check the board for moisture, corrosion or insect damage near the 8-pin EEPROM chip and clean it with IPA.
- If the code stays, the EEPROM data is corrupt. Reprogram it only if you have the correct data for that exact model; otherwise replace the board with the same part number.
8. Outdoor Fan Error (L3)
- Check the fan blade turns freely and is not cracked or touching the grille.
- Check the motor plug on the outdoor PCB.
- Like the indoor BLDC motor, check for supply voltages and the speed signal. Supply present but no rotation = motor; supply missing = outdoor PCB.
After Any Repair
Run the AC for at least 30 minutes in cooling mode. Check the running current with a clamp meter against the nameplate, confirm normal gas pressure and good cooling, and make sure no error code returns.
Easy Checks Anyone Can Do Before Calling a Technician
These safe steps fix many Blue Star error codes without opening the AC.
- Reset the AC: switch off the MCB for 5 minutes, then switch on.
- Clean the air filters: a dirty filter causes freezing (E2, Ed, FH) and high-temperature codes.
- Check the voltage: low or high voltage causes E0, E5, PH, PL and U3. Use a good stabiliser if your area has fluctuations.
- Clear the outdoor unit: remove boxes, leaves and plants; keep about 60 cm open space so hot air can escape (helps E1, E4, E8, P8).
- Wash the outdoor coil gently with low-pressure water if it is dusty (power off first).
- Check remote batteries and mode: a wrong mode or weak batteries can look like a fault.
- Empty the water tank on portable ACs (H8).
If the code returns after these checks, note the code, your model number and when the error appears, and call Blue Star customer care (1800 209 1177, toll-free) or a trained technician. Do not keep resetting compressor or over-current codes (E4, E5, H3, P5) — repeated restarts can damage the compressor.
Blue Star AC Error Code FAQ
What is E1 error in Blue Star AC? It depends on the model. On window ACs (L/G series) E1 is a room sensor failure; on RA/RB/TA/TB/DA/DB/FA split ACs it is an EEPROM error; on older and C/S-Series ACs it is high-pressure protection; on newer inverter models such as BO-IA518DLU and BO-5CNHW12QATU it means the outdoor coil temperature is too high.
What does E6 mean in Blue Star inverter AC? On most inverter models E6 is a communication error between the indoor and outdoor units. Check the connecting cable and terminals first.
What is H6 error in Blue Star AC? H6 means the indoor fan motor is not running or not giving feedback to the PCB. Check the fan capacitor, motor plug and the PCB fan circuit.
What is F1 and F2 error in Blue Star AC? F1 is an indoor room temperature sensor fault and F2 is an indoor coil (evaporator) sensor fault. Reconnecting or replacing the sensor usually fixes them.
What is P8 error in Blue Star AC? P8 is IPM (power module) overheating protection on the outdoor inverter board. Check the outdoor fan, heatsink and gas level.
Can I reset a Blue Star AC error code myself? Yes. Switch off the main MCB for 5 minutes and switch on again. If the code comes back, the fault needs repair.
Is Blue Star AC PCB repair costly? Sensor, fuse and capacitor repairs are cheap. A full inverter outdoor PCB replacement costs much more, so a technician should test the board before replacing it.
SEO Pack (for publishing)
| Field | Use this |
|---|---|
| SEO title (under 60 characters) | Blue Star AC Error Codes List & PCB Repair Guide 2026 |
| Meta description (under 160 characters) | All Blue Star AC error codes (E1, E6, F1, H6, P8 & more) by model series, with main problem and easy fix. PCB repair guide for technicians. |
| URL slug | /blue-star-ac-error-codes-pcb-repair |
| Focus keyword | Blue Star AC error codes |
| Secondary keywords | Blue Star inverter AC error code, Blue Star AC PCB repair, Blue Star AC E1 error, Blue Star AC E6 error, Blue Star AC H6 error, Blue Star split AC error code list, Blue Star AC problem and solution, Blue Star AC PCB repair step by step, Blue Star AC sensor value |
| Image alt text | Blue Star AC indoor unit showing error code on display |
| Schema | Add FAQPage schema using the FAQ section above |
Tips: keep the H1 as the title above, add a table of contents at the top, link to your related AC repair posts, and update the “as of” date when you add new codes.

Soldering Item’s
Other Item’s
PCB’s
Micro IC
DSP Card
Driver Card
Fuse & Holder
MOSFET & IGBT
Regulator IC